▄▄▄·▄▄▄ ▄▄▄ .    ▄▄▌ ▐ ▄▄▄▄ .     ▄▄·          ▄▄▌      ▄· ▄▄▄▄ ▄▄▄▄▄
    ▐█ ▀█▀▄ █▀▄.▀·    ██· █▌▐▀▄.▀·    ▐█ ▌▪    ▪    ██•     ▐█▪██▀▄.▀•██
    ▄█▀▀█▐▀▀▄▐▀▀▪▄    ██▪▐█▐▐▐▀▀▪▄    ██ ▄▄▄█▀▄ ▄█▀▄██▪     ▐█▌▐█▐▀▀▪▄▐█.▪
    ▐█ ▪▐▐█•█▐█▄▄▌    ▐█▌██▐█▐█▄▄▌    ▐███▐█▌.▐▐█▌.▐▐█▌▐▌    ▐█▀·▐█▄▄▌▐█▌·
     ▀  ▀.▀  ▀▀▀▀      ▀▀▀▀ ▀▪▀▀▀     ·▀▀▀ ▀█▄▀▪▀█▄▀.▀▀▀      ▀ • ▀▀▀ ▀▀▀
                                    ██████╗
                                    ╚════██╗
                                      ▄███╔╝
                                      ▀▀══╝
                                      ██╗
                                      ╚═╝

                       -*- Are We Cool Yet? Presents -*-                       

###############################################################################
#                                                                             #
#                     The Everyman's 43x (E43, E43x, E48)                     #
#                     A beginners printable pistol frame                      #
#                                    v1.0                                     #
#                                                                             #
###############################################################################
#                            /X> Release Notes <X\                            #
###############################################################################
#                                                                             #
#                            Second AWCY release!                             #
#                                                                             #
###############################################################################
#                               /X> Credits <X\                               #
###############################################################################
#                                                                             #
#                          [-+ Brought to you by +-]                          #
#                                                                             #
#             ︻╦╤─ Sigfried(Co-developer, primary 43x/48) ─╤╦︻              #
#               ︻╦╤─ 4myright(Co-developer, primary 43) ─╤╦︻                #
#                  ︻╦╤─ bitplumb(Head test engineer) ─╤╦︻                   #
#                                                                             #
#                          [-+ With the help of +-]                           #
#                                                                             #
#              Engarm(ongoing auto sear development assistance),              #
#           Because2nd(OEM measurements), All4one(Early CAD help),            #
#                         and v8vtwin(Moral Support)                          #
#                                                                             #
#                        [-+ Additional thanks to +-]                         #
#                                                                             #
#    Skyraze, Karver, Soggyknee, handydandy, all_i_no_is_gloc, mr_380_EZ,     #
#                          apophis9x19, [REDACTED],                           #
#                                                                             #
#                    and the entire Are We Cool Yet? team                     #
#                                                                             #
###############################################################################
#                           /X> Print Settings <X\                            #
###############################################################################
#                                                                             #
#   Filament: PLA+ or stronger                                                #
#   Temp: 205-225 (PLA)                                                       #
#   Frame orientation: Print magazine well down.                              #
#   Infill: 99% (gyroid pattern with tree supports preferred)                 #
#                                                                             #
###############################################################################
#                              /X> Materials <X\                              #
###############################################################################
#                                                                             #
#   1x SS80 builders kit including:                                           #
#                                                                             #
#   	1x combo front rail block                                             #
#                                                                             #
#   	1x single piece rear rail                                             #
#                                                                             #
#   	1x 4mm trigger pin                                                    #
#                                                                             #
#   	1x 3mm rear rail pin                                                  #
#                                                                             #
#   1x Glock 43/43x/48 parts kit including:                                   #
#                                                                             #
#   	1x barrel                                                             #
#                                                                             #
#   	1x upper parts kit                                                    #
#                                                                             #
#   	1x lower parts kit                                                    #
#                                                                             #
###############################################################################
#                            /X> Linked Guides <X\                            #
###############################################################################
#                                                                             #
#                         Hans Grabber builds a Glock                         #
#                                                                             #
###############################################################################
#                              /X> Assembly <X\                               #
###############################################################################
#                                                                             #
#                                [-+ Frame +-]                                #
#                                                                             #
#   1. Remove supports, taking care to clean out the sear pocket.             #
#                                                                             #
#   2. Check that all rails and pins fit. Ream out holes if required.         #
#                                                                             #
#   3. Install mag catch spring and mag catch.                                #
#                                                                             #
#   4. Install the rear rail.                                                 #
#                                                                             #
#   5. Install sear housing and trigger. Make sure all holes align            #
#      properly with the frame.                                               #
#                                                                             #
#   6. Install the last round hold open lever.                                #
#                                                                             #
#   7. Place the front rail into the frame.                                   #
#                                                                             #
#   8. Drive the 4mm pin through the front rail, last round hold open, and    #
#      trigger. (It can help to align these three components with a           #
#      smaller pin before driving through the 4mm pin.)                       #
#                                                                             #
#   9. Drive the 3mm pin through the rear rails and sear housing.             #
#                                                                             #
#   10. Install the takedown bar and spring in front of the combo rail.       #
#                                                                             #
#   11. Install a the slide, and rack the slide numerous times to ensure      #
#       function and ensure the rails are firmly seated.                      #
#                                                                             #
#   12. So anyway, get to blasting.                                           #
#                                                                             #
###############################################################################
#                             /X> Statistics <X\                              #
###############################################################################
#                                                                             #
#                    Combined round count from beta: 2195                     #
#                                                                             #
#                Max round count on one frame: 600 (4myright)                 #
#                                                                             #
#                  Max round count with different materials:                  #
#                                                                             #
#                          Nylonx: 600 and counting                           #
#                                                                             #
#                           Resin: 300 and counting                           #
#                                                                             #
#                           PLA+: 215 and counting                            #
#                                                                             #
#                  (give us a break theres an ammo shortage)                  #
#                                                                             #
###############################################################################
#                           /X> Troubleshooting <X\                           #
###############################################################################
#                                                                             #
#   Issue: Slide does not rack cleanly, or hangs up on the front of the       #
#   frame.                                                                    #
#                                                                             #
#   Solution: The SS80 rails have notoriously bad QC. Check your rails for    #
#   flatness and squareness. If that does not resolve the issue, check the    #
#   frame for warp. Even the slightest warp in the sear will result in        #
#   difficultly cycling.                                                      #
#                                                                             #
#   Issue: Mag catch does not allow the removal of OEM mags.                  #
#                                                                             #
#   Solution: Make sure you have printed the OEM mag catch, not the shield    #
#   mag catch. The printed Shield catch has a larger contact area to insure   #
#   retention and is not OEM compatable.                                      #
#                                                                             #
#   Issue: I have assembled the pistol and am not cool yet.                   #
#                                                                             #
#   Solution: Being cool is about the journey, not the destination.           #
#                                                                             #
###############################################################################
#                                                                             #
#                 -`-,-{@  AWCY? - Stronger Together  @}-,-`-                 #
#                          (oven appreciation group)                          #
#                  Join us at: https://www.AreWeCoolYet.WTF                   #
#                                                                             #
###############################################################################